Vol. 56 No. 5 (2024)

Back Matter

Many developing countries have high traffic accident rates due to the mixed traffic environment in which bicycles and motor vehicles travel in the same lanes. This paper examines the perceived risk among road users in mixed traffic. A questionnaire survey was used to obtain demographic information and self-reported risk perception among cyclists, motorcyclists, and drivers. Statistical analyses, including the T-test and ANOVA, were used to examine the relevant differences in risk assessment among the groups. The results demonstrate that the groups differ significantly in sociodemographic…

This study optimized the locations and sizes of wind-based distributed generators (WDGs) and solar photovoltaic-based distributed generators (PVDGs) to reduce the overall active power loss (OAPL) of an IEEE 85-bus distribution power system (DPS). Three meta-heuristic algorithms, including the Wild Horse Optimizer Algorithm (WHOA), the Archimedes Optimization Algorithm (AOA), and the Transient Search Optimization (TSO) algorithm, were applied and compared to each other to identify the most effective method for finding the best value of OAPL. Based on the analysis, WHOA outperformed the other…

Indonesia has 127 active volcanoes, which have to be monitored continuously in normal, eruption, or after-eruption conditions, to minimize the effects of disaster. Therefore, we have developed a four-wheeled mobile robot for both exploration and monitoring of volcanoes. To finish its mission on uneven terrain full of obstacles, the robot should be able to detect and avoid these obstacles. Therefore, real-time object detection was designed using the YOLOv5s deep learning algorithm, which was implemented on a Raspberry Pi3 for the front camera of the robot. Before it was tested on a real…

Carbon dioxide is a colorless, odorless, and non-flammable gas and is claimed to be the fourth most abundant in the earth

The material for a cutting tool needs to be carefully selected to withstand high temperatures during cutting and have good wear performance. The use of cutting tools made from cemented carbide material was studied due to its potential in terms of mechanical properties that are ideal at high temperatures up to 1000 °C and being cheaper than other materials. This investigation of the dry wear of this cutting material focused on temperatures of 25 °C, 200 °C, and 300 °C, with loads of 50 N, 100 N, and 150 N. The weight loss, friction coefficient, and change of the pin microstructure were…

In recent years, the development and implementation of artificial intelligence (AI) have attracted tremendous attention. The implementation of active control systems for building structures can be improved by using an AI controller. Non-AI controllers such as the Linear Quadratic Regulator (LQR) controller require full state variables of the structure to be measured, which is rarely feasible. To address this problem, two AI models, namely, artificial neural network (ANN) and fuzzy logic (FL), have been tried as AI-based controller in various studies. In the present study, both AI models were…

Mass concrete plays a crucial role in infrastructure development, yet its complex thermo-mechanical behavior poses challenges, especially in the construction of multi-layered structures like pier heads. This study investigated the thermo-mechanical behavior of a pier head during its concreting process in three stages, including the influence of temperature differences that impact the thermomechanical balance of the concrete. By utilizing the ABAQUS software, thermo-mechanical analysis was conducted to simulate temperature fluctuations during cement hydration. The model integrates thermal…

The planform design of a wind turbine blade influences its aerodynamic performance and noise characteristics, with the tip shape controlling vortex shedding, power, and noise. This study examined the tip shape’s effect on a small horizontal-axis wind turbine (HAWT). Field tests were conducted on three rotors: one with straight blades, one with low swept angle (12° and 61° sweep, 15° anhedral) blades, and one with high swept angle (32° and 72° sweep, 15° anhedral) blades. All had three blades, a tip speed ratio (TSR) of 5.24, and an NACA 4412 cross-section. The basic blade rotor and the…

On-land alluvial tin mining activities produce residual materials from mineral processing or mineral washing; the major one of these is quartz sand, which can be utilized in the manufacturing industry. As time goes by, the reserves of alluvial tin are decreasing, which is in line with the increasing residual material from abundant mineral processing. Mining procedures are carried out following the Indonesian government regulations, covering mining as well as reprocessing. This motivated us to evaluate the potential of quartz sand at two mining sites in Bangka and Belitung Islands. This study…

Transition metal-nitrogen-carbon (M/NC) demonstrates a promising effective electrocatalyst for enhancing oxygen evolution/reduction reactions (OER/ORR). However, synthesizing these catalysts is often complex, time-consuming, and involves hazardous solvents while producing a low yield. This work introduces a versatile, eco-friendly, and straightforward solvent-free method to produce M/NC (M = Co, Ni, and Fe) catalysts in ~3 h using a glucose, urea, and metal nitrate hydrate mixture. The high-yield M/NC catalysts exhibit a porous architecture and uniform distribution of metal nanoparticles…